Forum Magazine article prep

[StagnJag]

Hi All,

I am currently busy preparing the next installment of technical bits and bobs from the forum for the mag.

The following list is the selection I have picked. Probably too much to print, but better too much than too little!

1/4 Light seals http://tinyurl.com/y97qc8e
New Carpets to fit http://tinyurl.com/ya7zpyf
Power Steering Pipe (Low Pressure) http://tinyurl.com/ybgckr6
Leaded or unleaded http://tinyurl.com/ye2paho
Servo Service http://tinyurl.com/y9zfhq7
Aldi Digital Caliper (I had to try and sneak in a funny one!) http://tinyurl.com/yald826
Fitting New shocks and springs http://tinyurl.com/ych297d
Removing Water Pump. http://tinyurl.com/yclemnw

I might edit a couple of these out as I am in danger of taking over the whole mag at the moment!!!

I also want to add a bit about Stoneleigh, so a copy of any pics taken of the rabble would be great.

Finally, the reason for this post is that I am on the scrounge for photos. I have loads of text but very few photos and I don't want to make it too heavy to read. If anyone has any photos that would suit the above, please can you email them to me at dave@stagwiki.com. I have one for the 1/4 light rubbers (I have some here ready to fit).

Two I have picked out are vmad's water pump puller (http://tinyurl.com/yclemnw) and StuStags Drop link photo (http://tinyurl.com/ych297d). I would very much like a high res copy of your photos if you are happy for them to go in the mag.

Cheers

Dave

[grahamb]

imported post

Love the enthusiasm Dave and its still only the 8th.....

[StagnJag]

imported post

just trying to get it out of the way so I can rest easy!

[Andrew S]

imported post

Well done Dave

Andrew

[grahamb]

imported post

Glad to hear it Dave. Dont let it make you late to the pub on Wednesday though. Rumour has it that Ian is going to buy a round and your wouldnt want to miss that rare occasion

[StagnJag]

imported post

I'll make sure I am there nice and early then so I don't miss out!

[grahamb]

imported post

I am going to get there so I can get parked!

[NickA]

imported post

StagnJag wrote:

Hi All,

I am currently busy preparing the next installment of technical bits and bobs from the forum for the mag.

<snip>
I might edit a couple of these out as I am in danger of taking over the whole mag at the moment!!!

<snip> Cheers

Dave

Perhaps you could swap places with the Out and About section.That'll give you plenty of room

Gets coat; leaves building.

[jleyton]

imported post

NickA wrote:

Perhaps you could swap places with the Out and About section.That'll give you plenty of room

Gets coat; leaves building.

Here, here, too bloody true

[Ian B]

imported post

grahamb wrote:

Glad to hear it Dave. Dont let it make you late to the pub on Wednesday though. Rumour has it that Ian is going to buy a round and your wouldnt want to miss that rare occasion

Cheeky *******


only for those who turn up in a stag........................Graham!!!!

[KansasCityMilkman]

imported post

Dave wrote "I have one for the 1/4 light rubbers (I have some here ready to fit)."


Hi Dave, if you haven't got around to fitting yours I can let you have some pics of mine that I've just fitted.

KCM

[grahamb]

imported post

Ian B wrote:

grahamb wrote:

Glad to hear it Dave. Dont let it make you late to the pub on Wednesday though. Rumour has it that Ian is going to buy a round and your wouldnt want to miss that rare occasion

Cheeky *******


only for those who turn up in a stag........................Graham!!!!